60 lines
2.5 KiB
C++
60 lines
2.5 KiB
C++
#
|
|
# ***** BEGIN LICENSE BLOCK *****
|
|
#
|
|
# Copyright (C) 2009-2017 Olof Hagsand and Benny Holmgren
|
|
#
|
|
# This file is part of CLIXON
|
|
#
|
|
# Licensed under the Apache License, Version 2.0 (the "License");
|
|
# you may not use this file except in compliance with the License.
|
|
# You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing, software
|
|
# distributed under the License is distributed on an "AS IS" BASIS,
|
|
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
# See the License for the specific language governing permissions and
|
|
# limitations under the License.
|
|
#
|
|
# Alternatively, the contents of this file may be used under the terms of
|
|
# the GNU General Public License Version 3 or later (the "GPL"),
|
|
# in which case the provisions of the GPL are applicable instead
|
|
# of those above. If you wish to allow use of your version of this file only
|
|
# under the terms of the GPL, and not to allow others to
|
|
# use your version of this file under the terms of Apache License version 2,
|
|
# indicate your decision by deleting the provisions above and replace them with
|
|
# the notice and other provisions required by the GPL. If you do not delete
|
|
# the provisions above, a recipient may use your version of this file under
|
|
# the terms of any one of the Apache License version 2 or the GPL.
|
|
#
|
|
# ***** END LICENSE BLOCK *****
|
|
#
|
|
|
|
#
|
|
# Include this file in your application Makefile using eg:
|
|
# -include $(datarootdir)/clixon/clixon.mk
|
|
# then you can use the DIRS below in your install rules.
|
|
# You also get rules for the application configure file.
|
|
# NOTE: APPNAME must be defined in the local Makefile
|
|
|
|
clixon_DBSPECDIR=prefix/share/$(APPNAME)
|
|
clixon_SYSCONFDIR=sysconfdir
|
|
clixon_LOCALSTATEDIR=localstatedir/$(APPNAME)
|
|
clixon_LIBDIR=libdir/$(APPNAME)
|
|
clixon_DATADIR=datadir/clixon
|
|
|
|
# Rules for the clixon application configuration file.
|
|
# The clixon applications should be started with this fileas its -f argument.
|
|
# Typically installed in sysconfdir
|
|
# Example: APPNAME=myapp --> clixon_cli -f /usr/local/etc/myapp.conf
|
|
# The two variants are if there is a .conf.local file or not
|
|
.PHONY: $(APPNAME).conf
|
|
ifneq (,$(wildcard ${APPNAME}.conf.local))
|
|
${APPNAME}.conf: ${clixon_DATADIR}/clixon.conf.cpp ${APPNAME}.conf.local
|
|
$(CPP) -P -x assembler-with-cpp -DAPPNAME=$(APPNAME) $< > $@
|
|
cat ${APPNAME}.conf.local >> $@
|
|
else
|
|
${APPNAME}.conf: ${clixon_DATADIR}/clixon.conf.cpp
|
|
$(CPP) -P -x assembler-with-cpp -DAPPNAME=$(APPNAME) $< > $@
|
|
endif
|